This past week, there was gentleman who came into Mees with questions about the waterproof shower system we carry called Wedi, and what we knew about ADA codes. I had asked him what his project was and he informed me that he was remodeling an apartment bathroom to be ADA compliant. He said the tenants of the apartment needed to be able to navigate throughout the space in a wheelchair. He had shown me his quick sketch of the shower and I saw that he did not have enough space for a five foot turning radius for an accessible wheel chair which is crucial for his  client. His stand up shower was only three feet in deep and four feet wide and he had a toilet sticking out from the right wall that took up close to two feet. As the toilet was protruding into the walk space, his options for fixing the issue were to orient the toilet in a different direction and change the plumbing, knock out the opposing wall to make for more width in the shower, drop his shower pan so he did not need to build a  small ramp for the wheel chair, or potentially water proof the bathroom and make the entire bathroom as accessible so his client did not have to squeeze into a tight shower. My boss and I reviewed our Wedi shower pans with him and the shower drain options. We sell three by five, five by six and five by seven shower pans which you can cut down to fit your shower better. We also have on center drains and offset shower drains both in circular and linear options.

One of his concerns was whether or not he needed 1 x1 inch tiles or if he could use 2 x 2 inch. If he used the larger 2 x 2 size tiles, he was concerned there would not be as great of a pitch to the shower drain, which could cause water to build up and not drain out. If he used the smaller  1 x 1 shower tile, he thought he may not have to change out the shower pan or drop it lower. As he was not 100 percent certain on all ADA codes, he shared with me that he really enjoyed doing this kind of remodel work  (ADA remodel) as he felt he was giving back and doing good in some form of way, he really wanted to learn how to properly build an ADA compliant space.To my surprise, he said he had contacted a number of sources to try to learn more about the standards and requirements, having contacting contractors and even officials who are in part of the ADA legislation. However, he struggled to get any solid help or feedback. I had suggested he get in contact with a certified interior designer, particularly one who specializes in kitchen and bath who has knowledge and experience in ADA accessible spaces. He exclaimed that was the best suggestion he has had yet. Moreover, he did not even realize that a wheel chair needed at least a five foot turning radius. While  I am still a student and am no expert in this area of design, I felt like I was applying what I had learned in school at work and was able to help someone else in the design work field advance on a job.




This past week had been a fast and crazy one. For studio on Monday, my class took a roadtrip to Chicago and arrived back in Lexington on Wednesday. Needless to say, my work week started on Thursday instead of Tuesday. However, I jumped back into the showroom, sorting through new sample pieces and contacting the manufacturers for updated price sheets. One of the new series that Mees received was Soho’s new line of Baroque mosaics, featuring a Crackled, Floret, Lantern, and Ornate collection. All of the Baroque collections came in four color ways in a crackled or glazed finish. These are some of the more unique series that we have in our showroom as we do not have matching collections to the Floret, Lantern, or Ornate. Moreover, I am personally a fan of the Floret collection due to its organic lines, shape and color ways. The Floret also features a blend of both glazed and marble tile within the pattern. Overall, the design of the mosaic  reminds me of dolphin tails or sea plants.

SOHO’S website:


BLOG 7: 6 FOOT, 7 FOOT, 8 FOOT….

One of the most applicable tasks that I have had to do at Mees which I can apply to my own work in design is calculating square footage. Before I began working at Mees tile,  I knew VERY little about what a  “square foot” actually meant, or how many inches are in a square foot. One thing that I had to pick up quickly was standard tile dimensions and how to calculate how much square footage there was per installation job. A square foot is 12 inches by 12 inches, which gives you 144 square inches. So, 144 inches equals one square foot. If I had to find out how many square feet there were in a shower install, I would take the number of inches provided per side of wall (ex. 60 inches x 108 inches) and divide it by 144 gives you the total square feet of that particular part of the shower. In this case there would be 45 square feet on that one side of the wall. If the inches were converted already into feet (60 inches = 5 feet) than you would multiply 6 by 9 (108 inches = 9 feet) to get 45 square feet. All this may seem like simple math, but sometimes it can get confusing when you are converting feet to inches or vise versa.

This past Tuesday, I helped one of my co-workers find the approximate square feet needed to tile part of her client’s bathroom. Below I have include a quick sketch and calculations to demonstrate how I figured the total square feet of the shower and half wall.




This week at Mees, we had a number of customers come back in to return samples, check out new samples, and place orders. One of the couples that I had blogged about previously, came back to review the travertine samples they were interested in ordering for their bathroom install. My manager, Elizabeth and I sat down with the very excited and curious couple to discuss their options as to whether they wanted to install natural travertine on their floor or if they wanted to go the safer route and install porcelain tile that would mimic the look of the natural stone. The benefits of using a porcelain tile versus a natural stone for the field tile (the main floor tile) would be that the couple would not have to seal it as it is not porous or a natural material which requires more care and maintenance. Moreover, porcelain is more dense and durable than travertine which is a much more delicate and porous material, even more so than marble or granite. The couple had realized that after they had check out an 18×18″ field tile which accidentally broke in half while they had it. This thought was further supported by the exchange I had with one of the sales reps from a manufacturer that produced one of the travertine samples the couple was interested in. The rep explained how his company hand makes the travertine tiles and that they are able to take custom orders, but are unable to produce 18×18″ field tiles due to its fragility in that size.

After showing the couple numerous porcelain samples we stock, they realized it would be more economical and less maintenance required if they went with this option for the bathroom floor. However, they  still wanted to integrate the look of durango into the space by using the cobbled edge 3×6″ travertine subway tile inside the shower 2/3rds of the way up the walls. The couple also decided on using a durango pencil liner to use as transition piece between the wall field tile and the subway tile. For the shelving, the couple decided to purchase one of our Wedi products, a 100 percent waterproof recessed vertical shelf. Overall, the couple was very pleased with the design of their shower install and plan on placing their order after they checking out a field tile to be 100 percent certain on their choice.

Also, on Saturday, Elizabeth and  I worked on redoing a couple of our wall displays. The beautiful marble mosaics we hung are produced by the manufacturer, Adko. While one may not think hanging tile mosaics would take a long time, it took the two of us a bit of time nailing, hammering and re-nailing to get the mosaics balanced, centered and just right!




This past week at Mees flew by…partly because we were so busy with customers and in-store  interior changes! On Tuesday, my manager, Michele, was out of town so she had made a helpful to-do list for my co-worker Jennifer, Elizabeth and myself to try to tackle. First on the list was to pull samples that were no longer carried by its manufacturers. One of the samples was from the MSI Ledgerstone series that I have previously blogged  about. Others were  samples from the manufacturer Antico Stone, within the Ciotolli Series.  What I have learned from working with manufacturers and meeting different reps is that certain product can be back-ordered (depending on popularity and stock),   or be discontinued depending on frequency of orders, etc. Sometimes certain manufacturers allow for tile only to be ordered in palettes . This can cause the estimated shipping time to vary depending on whether or not there are multiple tile orders to make up one palette to send.

After we sort through old, low in stock, or discontinued samples, we allow for new space for other product to be displayed. This past week, Elizabeth helped reorganize one of our sale display racks, which I believe she had organized based on tile dimensions and color.  (I have included a picture at the bottom!)

Moreover, this past week I had followed up with a customer on their interest in the Interceramic Retro Series 8×8 tile in the tile colors, burgundy and almond. The customer, based out of Texas, needed 145 SF of each color for a job in Lexington. My customer had called a week ago to find out if we could special order this particular tile because we do not stock it in our showroom. After contacting Interceramic and speaking with a sales rep, I learned that they had both colors in stock, but I had to get a direct shipping quote via a ground shipping company. After phoning a number of shipping companies, I received the best shipping quote from FedEx, which I then informed my customer on their approximate cost for special ordering. After a week, my customer had given me the OK to place the order and get it on its way. From there, I had to fill out a special order form which included information such as: manufacturer, series, color, dimensions, customer contact information, etc. This is important as we fax our special orders to our headquarters in our Louisville location who places and handles all special orders, fabricating, and stock  transfers that are distributed. Not often do I always get to write up special order forms, so when I do,  I see them as a great learning experience, as it helps me better understand the process between the manufacturer, distributor and customer.

Something that was exciting that I got to see take place in the shop was a new install of a wall mosaic that my manager had picked out to have on display. What was really neat about this tile installation was that it was taking place while Elizabeth and I were working so we got the chance to sit back and watch the layment process unfold. Through the process, I noted that our trusted tile-man used a trowel an rubber hammer to thin-set, tile and grout.  I have include photos to help show a little of the process below!



Elizabeth sorting through  one of our sale displays!IMG_3741.jpg


Our mosaic tile getting laid!